94_LightningSVT
Member
1994 F-150 Lightning
158,000+ miles
All options available for the year - center seat, keyless entry/light convenience group, tube bumper, sliding rear window, towing package
Ford Motorsport Mass Air Kit
Roll pan
Bought in July of '14 from a local guy. I'm the 4th owner. Was bone stock except for mass air kit, roll pan, battery, spark plugs, tires, cheap toneau cover, and missing fog lamps.
Have build sheet from SVT and from Ford/Helm.
Clean carfax. But I can tell you most of the sheet metal has been replaced due from the semi restoration. Hood/fender/box/outer rocker panels/radiator support - this is all I could see. Truck wasn't driven much in the last few years before I got it.
Was semi restored a few years back by the original owner. Painted then. No rust except for cab corners and passenger dog leg (door jam rear corner). Wheel arches and other common rust/rot areas are clean.
It's a driver but has its nice points. Everything works other than the first 2 speeds for the blower motor. There is a slight exhaust leak on the passenger side header flange on the far rear cylinder. Too cold out to play with it to figure it out.
Struckby Battery/Alternator cables - 1/15
Bilstein Shocks - 7/14
New front spring pockets/radius arm brkts - 7-14
Braided brake lines - 7/14
Smog pump delete w/pulley - 7/14
Edelbrock Aluminum High Flow Water Pump - 7/14
Summit/Northern Aluminum radiator - 7/14
Stock f-150 aluminum 15" wheels with new winter tires (2000 miles) - 12/14
Screamin' Demon ignition coil - 1/15
Dyna Mod - 1/15
Bassani Shorty Headers, midpipe, and catback exits in front of axle - 7/14
Spark Plugs/PCV - 7/14
All coolant hoses - 7/14
Front brake pads hardware - 7/14
Rear brake hardware - 7/14
Tweecer (not RT) - 1/15 - (only used to turn off EGR)
New fog lamp lenses and pigtails/bulbs w/used brackets - 7/14
Ball joints -7/14
Steering from pitman arm to spindles replaced - 7/14
Polyurethane radius arm/front swaybar/axel pivot bushings - 7/14
Used white tube bumper - 1/15
Not Installed:
B&M Aluminum Trans Pan
Blower motor resistor
220 Amp Alternator
Lug nuts
Struckby fan controller
75mm throttle body BBK
EGR delete plate - to delete EGR spacer between TB and intake
Underdrive Set
Asking $6000 obo
Located in Southeast Michigan
158,000+ miles
All options available for the year - center seat, keyless entry/light convenience group, tube bumper, sliding rear window, towing package
Ford Motorsport Mass Air Kit
Roll pan
Bought in July of '14 from a local guy. I'm the 4th owner. Was bone stock except for mass air kit, roll pan, battery, spark plugs, tires, cheap toneau cover, and missing fog lamps.
Have build sheet from SVT and from Ford/Helm.
Clean carfax. But I can tell you most of the sheet metal has been replaced due from the semi restoration. Hood/fender/box/outer rocker panels/radiator support - this is all I could see. Truck wasn't driven much in the last few years before I got it.
Was semi restored a few years back by the original owner. Painted then. No rust except for cab corners and passenger dog leg (door jam rear corner). Wheel arches and other common rust/rot areas are clean.
It's a driver but has its nice points. Everything works other than the first 2 speeds for the blower motor. There is a slight exhaust leak on the passenger side header flange on the far rear cylinder. Too cold out to play with it to figure it out.
Struckby Battery/Alternator cables - 1/15
Bilstein Shocks - 7/14
New front spring pockets/radius arm brkts - 7-14
Braided brake lines - 7/14
Smog pump delete w/pulley - 7/14
Edelbrock Aluminum High Flow Water Pump - 7/14
Summit/Northern Aluminum radiator - 7/14
Stock f-150 aluminum 15" wheels with new winter tires (2000 miles) - 12/14
Screamin' Demon ignition coil - 1/15
Dyna Mod - 1/15
Bassani Shorty Headers, midpipe, and catback exits in front of axle - 7/14
Spark Plugs/PCV - 7/14
All coolant hoses - 7/14
Front brake pads hardware - 7/14
Rear brake hardware - 7/14
Tweecer (not RT) - 1/15 - (only used to turn off EGR)
New fog lamp lenses and pigtails/bulbs w/used brackets - 7/14
Ball joints -7/14
Steering from pitman arm to spindles replaced - 7/14
Polyurethane radius arm/front swaybar/axel pivot bushings - 7/14
Used white tube bumper - 1/15
Not Installed:
B&M Aluminum Trans Pan
Blower motor resistor
220 Amp Alternator
Lug nuts
Struckby fan controller
75mm throttle body BBK
EGR delete plate - to delete EGR spacer between TB and intake
Underdrive Set
Asking $6000 obo
Located in Southeast Michigan
Last edited: