CalTracs

11-04-2001, 08:10 AM

Had a problem with pinion wind up. Had almost cut an aluminum driveshaft in half and broke rear u joint/bent to the point that needle bearing were falling out of stock shaft. Got CalTracs from Mark. WOW!!! Not only did it fix my problem but took .10 off my 60' times. I didn't think I had any traction problems with 1.82-1.85 60' times but with CalTracs 5 runs 1.74 to 1.75. The Truck feels completely different (but good) on the launch. Even if you don't have a traction problem you NEED them.
Steve

11-04-2001, 01:07 PM

How much of a PITA are they to install? Any cutting or chopping, or straight bolt-on?

Thanks

------------------
Mike Hague
'99 L Black 13.36@102.26
'95 Cobra R 13.18@106+
'91 GMC Syclone 12.0's@111.5,,,so far

11-04-2001, 11:42 PM

Hey Mike,

A straight bolt on. Let me know if your interested. I can ship you out a set anytime.
Mark/LFP

11-09-2001, 12:24 PM

How much do they cost? I am interested in doing some upgrades to my suspension this winter because I don't need any failures like that.

------------------
Black 95 # 1356
NLOC # 218
13.24@99.04 1.78 60'
There is nothing made
that can't be sprayed

11-09-2001, 02:05 PM

Hey Keith,

You have mail. Gen1 and Gen2 Cal-Tracs in stock.
Mark/LFP

11-04-2001, 08:10 AM	#1 (permalink)
MYREDTOY Guest Posts: n/a View this user's gallery iTrader: / %	CalTracs Had a problem with pinion wind up. Had almost cut an aluminum driveshaft in half and broke rear u joint/bent to the point that needle bearing were falling out of stock shaft. Got CalTracs from Mark. WOW!!! Not only did it fix my problem but took .10 off my 60' times. I didn't think I had any traction problems with 1.82-1.85 60' times but with CalTracs 5 runs 1.74 to 1.75. The Truck feels completely different (but good) on the launch. Even if you don't have a traction problem you NEED them. Steve

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode




Home \| Classified Ads \| Gallery \| Join the Club \| Register on the Forum \| Merchandise \| Supporting Vendors \| Chat

11-04-2001, 01:07 PM	#2 (permalink)
Hamrhead Guest Posts: n/a View this user's gallery iTrader: / %	How much of a PITA are they to install? Any cutting or chopping, or straight bolt-on? Thanks ------------------ Mike Hague '99 L Black 13.36@102.26 '95 Cobra R 13.18@106+ '91 GMC Syclone 12.0's@111.5,,,so far

11-04-2001, 11:42 PM	#3 (permalink)
Lightninforce Guest Posts: n/a View this user's gallery iTrader: / %	Hey Mike, A straight bolt on. Let me know if your interested. I can ship you out a set anytime. Mark/LFP

11-09-2001, 12:24 PM	#4 (permalink)
crashbach Guest Posts: n/a View this user's gallery iTrader: / %	How much do they cost? I am interested in doing some upgrades to my suspension this winter because I don't need any failures like that. ------------------ Black 95 # 1356 NLOC # 218 13.24@99.04 1.78 60' There is nothing made that can't be sprayed

11-09-2001, 02:05 PM	#5 (permalink)
Lightninforce Guest Posts: n/a View this user's gallery iTrader: / %	Hey Keith, You have mail. Gen1 and Gen2 Cal-Tracs in stock. Mark/LFP