Lookiing for LHBLO, and probably sstock..

redroan351 · 03-31-2008, 02:15 AM

If anybody could help with the bin and def files for the C3P3 that I have in my 93. I thought I sent this at the same time I sent an email to sstock, it's a bit long but I hoped I could find help here with the lightnings rather than an old mustang forum. Have the Moates, I think it's going to be a great tool, I've already learned alot, and almost ready to wade in..

So to sstock or anybody that could donate some patients and guidance. I was wondering if you could help me with the LHBLO bin and def files. For some reasone I can't find them for download except on the yahoo tweecer
which hasn't confirmed my membership yet.

I also wondered if you could help me with a base tune because I am using the Moates Burn1 with the eproms and only have the Bosch o2 for the wideband logger but cant get the logger yet. Though I think there is an unused connector on the Lightning for a HEGO that I wonder if I could utilize, and I bought a Haze meter from Advanced that has four wires and says air/fuel. Also I might be able to go use the NGS at the dealer.

I like the EEC Analizer and Binary Editor programs and for now could benifit
with some basic stuff.

I have 93 L with C3P3, honed .040 over, Gasket matched Port and pollish on the gt40's, custom ground cam(flat tappet) from cammotion, with 1.77 Roller rockers, 11/2 " phpenolic spacer, I did the resistor trick and removed the EGR sensor entirely, blocked the hole and plugged the intake hole for it, though I'd like finish it off with the tune, and also did the resistor stuff for the EVP, DPFE, and Canister Purge Valve, No smog stuff hooked up, no Catalytic coonverters with tock headers and flowmasters on each pipe,(though I'll be getting maybe Hookers? soon) It has a Factory tech Monster Box and will chirp a third at about 70-75.

I also have an electric fan with shroud and resister attached from a 98 Merc
Grand Marquis I'd like to get on there.

I realize you can't write me a tune but I thought it might help to say what's in it. Any help would be so appreciated. I'm a ford factory trained techthough I left the dealer a while back, I understand the pids and what I think I need to do but I'm not super sure about which software needs me to use offsets and that kind of thing.

I hope this wasn't too long, my nloc is redroan351, and thanks for anything you can do. Roan

kbconv · 04-17-2008, 07:09 PM

Here's a list of bins.

Index of /bins

If you try C3P2 or C3P3 and it works let me know. In CalEdit my C.I.D. shows up as 282 so I don't know if the file is corrupt or what.

03-31-2008, 02:15 AM	#1 (permalink)
redroan351 Registered User Join Date: Mar 2003 Location: Baton Rouge,La<>Bay Area, Ca Posts: 72 View this user's gallery iTrader: 0 / 0%	Lookiing for LHBLO, and probably sstock.. If anybody could help with the bin and def files for the C3P3 that I have in my 93. I thought I sent this at the same time I sent an email to sstock, it's a bit long but I hoped I could find help here with the lightnings rather than an old mustang forum. Have the Moates, I think it's going to be a great tool, I've already learned alot, and almost ready to wade in.. So to sstock or anybody that could donate some patients and guidance. I was wondering if you could help me with the LHBLO bin and def files. For some reasone I can't find them for download except on the yahoo tweecer which hasn't confirmed my membership yet. I also wondered if you could help me with a base tune because I am using the Moates Burn1 with the eproms and only have the Bosch o2 for the wideband logger but cant get the logger yet. Though I think there is an unused connector on the Lightning for a HEGO that I wonder if I could utilize, and I bought a Haze meter from Advanced that has four wires and says air/fuel. Also I might be able to go use the NGS at the dealer. I like the EEC Analizer and Binary Editor programs and for now could benifit with some basic stuff. I have 93 L with C3P3, honed .040 over, Gasket matched Port and pollish on the gt40's, custom ground cam(flat tappet) from cammotion, with 1.77 Roller rockers, 11/2 " phpenolic spacer, I did the resistor trick and removed the EGR sensor entirely, blocked the hole and plugged the intake hole for it, though I'd like finish it off with the tune, and also did the resistor stuff for the EVP, DPFE, and Canister Purge Valve, No smog stuff hooked up, no Catalytic coonverters with tock headers and flowmasters on each pipe,(though I'll be getting maybe Hookers? soon) It has a Factory tech Monster Box and will chirp a third at about 70-75. I also have an electric fan with shroud and resister attached from a 98 Merc Grand Marquis I'd like to get on there. I realize you can't write me a tune but I thought it might help to say what's in it. Any help would be so appreciated. I'm a ford factory trained techthough I left the dealer a while back, I understand the pids and what I think I need to do but I'm not super sure about which software needs me to use offsets and that kind of thing. I hope this wasn't too long, my nloc is redroan351, and thanks for anything you can do. Roan

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode




Home \| Classified Ads \| Gallery \| Join the Club \| Register on the Forum \| Merchandise \| Supporting Vendors \| Chat

04-17-2008, 07:09 PM	#2 (permalink)
kbconv Nashville Join Date: May 2005 Location: Nashvegas, TN Posts: 246 View this user's gallery iTrader: 2 / 100%	Here's a list of bins. Index of /bins If you try C3P2 or C3P3 and it works let me know. In CalEdit my C.I.D. shows up as 282 so I don't know if the file is corrupt or what.