direction sheet for a granatelli, metco, motoblue

srteric · 12-28-2007, 03:05 PM

pulley with ring and hub anyone have the sheet for installing? Torque of the bolts?

bgstew6 · 12-28-2007, 03:22 PM

what plugs you running? are you talking bout shortening the ropes...?

7mm bolts only need to be snugged IIRC its like 19in lbs....just snug is all you need.

srteric · 12-28-2007, 03:32 PM

this is for a pulley 6 pounder, I see the stock bolt is 14mm to remove it but need the torque for the new pulley 3 bolts.

bgstew6 · 12-28-2007, 03:39 PM

the three bolts that hold the hub to the crank.....use some blue loctite and tq them to 40ftlbs

yes its 14mm for the stock crank pulley....its left hand thread FYI, righty loosely lefty tighty

bgstew6 · 12-28-2007, 03:41 PM

rpm outlet is good for something....here ya go..

ASP Overdrive 5.4L Blower Crank Pulley Installation (281) 261-6244

srteric · 12-28-2007, 03:46 PM

Hey thanks Eric

srteric · 12-28-2007, 03:51 PM

the previous owner gave me a 6 pound hub and ring, MAC 95 mm setup, and a sct chip, he said install it all, you will be amazed, he had it all on a 2002 HD truck he had, I have a 2003 Lightning, I put the MAC on today, was easy.

12-28-2007, 03:05 PM	#1 (permalink)
srteric Registered User Join Date: Jan 2007 Location: Belews Creek, NC Posts: 196 View this user's gallery iTrader: 0 / 0%	direction sheet for a granatelli, metco, motoblue pulley with ring and hub anyone have the sheet for installing? Torque of the bolts? Last edited by srteric; 12-28-2007 at 03:33 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode




Home \| Classified Ads \| Gallery \| Join the Club \| Register on the Forum \| Merchandise \| Supporting Vendors \| Chat

12-28-2007, 03:22 PM	#2 (permalink)
bgstew6 ResFirma Mitescere Nescit Join Date: Aug 2005 Location: CHarleston, SC Posts: 4,119 View this user's gallery iTrader: 9 / 100%	what plugs you running? are you talking bout shortening the ropes...? 7mm bolts only need to be snugged IIRC its like 19in lbs....just snug is all you need.

12-28-2007, 03:32 PM	#3 (permalink)
srteric Registered User Join Date: Jan 2007 Location: Belews Creek, NC Posts: 196 View this user's gallery iTrader: 0 / 0%	this is for a pulley 6 pounder, I see the stock bolt is 14mm to remove it but need the torque for the new pulley 3 bolts.

12-28-2007, 03:39 PM	#4 (permalink)
bgstew6 ResFirma Mitescere Nescit Join Date: Aug 2005 Location: CHarleston, SC Posts: 4,119 View this user's gallery iTrader: 9 / 100%	the three bolts that hold the hub to the crank.....use some blue loctite and tq them to 40ftlbs yes its 14mm for the stock crank pulley....its left hand thread FYI, righty loosely lefty tighty

12-28-2007, 03:41 PM	#5 (permalink)
bgstew6 ResFirma Mitescere Nescit Join Date: Aug 2005 Location: CHarleston, SC Posts: 4,119 View this user's gallery iTrader: 9 / 100%	rpm outlet is good for something....here ya go.. ASP Overdrive 5.4L Blower Crank Pulley Installation (281) 261-6244

12-28-2007, 03:46 PM	#6 (permalink)
srteric Registered User Join Date: Jan 2007 Location: Belews Creek, NC Posts: 196 View this user's gallery iTrader: 0 / 0%	Hey thanks Eric

12-28-2007, 03:51 PM	#7 (permalink)
srteric Registered User Join Date: Jan 2007 Location: Belews Creek, NC Posts: 196 View this user's gallery iTrader: 0 / 0%	the previous owner gave me a 6 pound hub and ring, MAC 95 mm setup, and a sct chip, he said install it all, you will be amazed, he had it all on a 2002 HD truck he had, I have a 2003 Lightning, I put the MAC on today, was easy.